Saturday, 9 February 2013

CCNA 3 Final Question Answer, CCNA 3 Answer




Part-1
1. A wireless client is attempting to establish a connection with a wireless access point. What process does the client use to discover the access points which are available to it?
probing
beaconing
association
authentication

CCNA 3 Final Exam Answer, CCNA 3 Final

CCNA-3 FInal Question and Answer




Description: http://ev-iip.netacad.net/assessment/images/21269.jpg
1. Refer to the exhibit. After entering the commands in the exhibit, the administrator receives a “password required, but none set” message when attempting to connect to S1. What is the problem?
The enable secret password was not set.
S1 does not have login configured on the vty lines.
S1 does not have a password configured for the vty lines.
The crypto key is not properly configured to generate passwords.
The VLAN1 interface has not be enabled with the no shutdown command.
2. Which CLI mode allows users to access all device commands, such as those used for configuration, management, and troubleshooting?
user EXEC mode
privileged EXEC modeglobal configuration mode
interface configuration mode
Description: http://ev-iip.netacad.net/assessment/images/16202.jpg
3. Refer to the exhibit. Which Spanning Tree Protocol version is in effect?
Per VLAN Spanning Tree (PVST)
Per VLAN Spanning Tree + (PVST+)
Common Spanning Tree (CST)
Rapid Spanning Tree Protocol (RSTP)Multiple Spanning Tree Protocol (MSTP)

Description: http://ev-iip.netacad.net/assessment/images/19930.jpg
4. Refer to the exhibit. A network administrator has segmented the network into two VLANs and configured Router1 for inter-VLAN routing. A test of the network, however, shows that hosts on each VLAN can only access local resources and not resources on the other VLAN. What is the most likely cause of this problem?
Switch port Fa0/1 is not trunking.Router interface Fa0/0 is possibly down.
No routing protocol is configured on Router1.
One of the router subinterfaces is possibly down.

Description: http://ev-iip.netacad.net/assessment/images/18165.jpg
5. Refer to the exhibit. Hosts A and B, connected to hub HB1, attempt to transmit a frame at the same time but a collision occurs. Which hosts will receive the collision jamming signal?
only hosts A and B
only hosts A, B, and Conly hosts A, B, C, and D
only hosts A, B, C, and E

Friday, 1 February 2013

CCNA Final Question and Answer


Total 3 Set Question and Answer  

Set-1

1. Which of the following are required when adding a network to the OSPF routing process configuration?network addressloopback address
autonomous system number
subnet mask
wildcard maskarea ID
2. Which of the following are primary functions of a router? (Choose two.)
packet switching
microsegmentation
domain name resolution
path selection
flow control
CCNA2 Final Exam
3. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.


CCNA2 Final Exam
4. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)
10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
192.168.2.0/24

5. When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?
when there is a low bandwidth connection
when the connection is on a shared medium
when the connection is serial instead of Ethernet
when the link is always busy
CCNA2 Final Exam
6. Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?
C-B-E-D
C-B-A-D
C-F-E-D
C-F-B-A-D
C-F-E-A-D
7. What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks?
hello
LSU
LSR
DBD
LSAck
CCNA2 Final Exam
8. Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured?
the IP address of the Fa0/0 interface at R1
the IP address of the S0/0/1 interface at R2
the IP address of the S0/0/0 interface at R1
the subnet mask of the S0/0/1 interface at R2
CCNA2 Final Exam
9. Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2?
192.168.1.0/24
192.168.0.0/24
192.168.0.0/22
192.168.1.0/22
CCNA2 Final Exam
10. Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.)
R 172.16.1.0/24 [120/1] via 192.168.3.0, 00:00:24, Serial0/0/0
R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1
R 192.168.9.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0
R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0
R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0
11. A router boots and enters setup mode. What is the reason for this?
The IOS image is corrupt.
Cisco IOS is missing from flash memory.
The configuration file is missing from NVRAM.
The POST process has detected hardware failure.
CCNA2 Final Exam
12. Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?
Compared to RIP, EIGRP has a lower administrative distance.
Compared to EIGRP, RIP has a higher metric value for the route.
Compared to RIP, the EIGRP route has fewer hops.
Compared to RIP, EIGRP has a faster update timer.


See More >>

Monday, 31 December 2012

CCNA 2 Final Skill Exam Simple, eigrp configureation Solution



Answer:

· The router name is EB2.
Router(config)# hostname EB2

· The privileged EXEC mode uses the following encrypted password: class.

EB2(config)#enable secret class

Enable Telnet and console line logins and use the following password: cisco.

EB2(config)#line vty 0 4
EB2(config)#password class
EB2(config)#login
EB2(config)#exit

See More>>