Monday, 31 December 2012

CCNA 2 Final Skill Exam Simple, eigrp configureation Solution



Answer:

· The router name is EB2.
Router(config)# hostname EB2

· The privileged EXEC mode uses the following encrypted password: class.

EB2(config)#enable secret class

Enable Telnet and console line logins and use the following password: cisco.

EB2(config)#line vty 0 4
EB2(config)#password class
EB2(config)#login
EB2(config)#exit

See More>>

Friday, 28 December 2012

CCNA 2 Final Exam Question and Answer, ccna 2 Final Answer

CCNA 2 Final Exam Question ans Answer

Sample-1

1. Which of the following are required when adding a network to the OSPF routing process configuration?network addressloopback address
autonomous system number
subnet mask
wildcard maskarea ID
2. Which of the following are primary functions of a router? (Choose two.)
packet switching
microsegmentation
domain name resolution
path selection
flow control
CCNA2 Final Exam
3. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.


CCNA2 Final Exam
4. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)
10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
192.168.2.0/24


See More>>

Thursday, 27 December 2012

CCNA 2 Final Question and Answer

CCNA 3 Final Question and Answer

CCNA2 thumb CCNA 2 Final Exam V4.0 Answers
Refer to the exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)
Paris(config)# router eigrp 100
Paris(config)# router eigrp
Paris(config-router)# network 192.168.6.0
Paris(config-router)# network 192.168.7.0
Paris(config-router)# network 192.168.8.0
Paris(config-router)# network 192.168.9.0

2. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?

D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

Wednesday, 26 December 2012

MY ALL POST

My All Post

V-1

1. Which of the following are required when adding a network to the OSPF routing process configuration?network addressloopback address
autonomous system number
subnet mask
wildcard maskarea ID
2. Which of the following are primary functions of a router? (Choose two.)
packet switching
microsegmentation
domain name resolution
path selection
flow control
CCNA2 Final Exam
3. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.


CCNA2 Final Exam
4. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.)
10.0.0.0/8
64.100.0.0/16
128.107.0.0/16
172.16.40.0/24
192.168.1.0/24
192.168.2.0/24

5. When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?
when there is a low bandwidth connection
when the connection is on a shared medium
when the connection is serial instead of Ethernet
when the link is always busy
CCNA2 Final Exam
6. Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down?
C-B-E-D
C-B-A-D
C-F-E-D
C-F-B-A-D
C-F-E-A-D

See More>>


CCNA 2 Module Answer

My Post...... About CCNA 2 Module

1. Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?
Router1(config-router)# network 192.168.16.0
2. What is the maximum network diameter permitted by the default metric of RIPv2?
15 hops
3. Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 isconfigured on router B?

See More>>

ccna 2 chapter 1 question and answer, cisco question and answer, cisco tutorial question ans answer

CCNA 2 Chapter 1 Answer

1If a router cannot find a valid configuration file during the startup sequence, what will occur?
The startup sequence will reset.
The router will prompt the user for a response to enter setup mode.
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last valid configuration.
The router will monitor local traffic to determine routing protocol configuration requirements.
2.
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The destination networks do not exist.
The IP addresses on the router interfaces must be configured as network addresses and not host addresses.
The interfaces must be enabled with the no shutdown command.
Each interface must be configured with the clock rate command.


See More>>